Tuesday, December 24, 2019

Physics Lab Report - 3601 Words

ABSTRACT: The lab of one dimensional motion is a series of experiments that deal with different types of motion in a single direction. In the first experiment, one dimensional motion of a small cart on an air track is measured in a one photogate system. The acceleration was calculated by the infrared light emitting electrode of the photogate sensing the slacks on the picket fence. The calculation for gravity yielded 9.63 m/s^2, which is consistent with the accepted value of 9.8m/s^2. In the second experiment, acceleration of a cart traveling down a slight incline was measured with a two photogate method. Gravity was calculated and yielded a value of 8.7429, a bit lower than the accepted value of 9.8 m/s^2. The third experiment was†¦show more content†¦The second length of time will be the time in between when the first photogate is blocked until when the second photogate is unblocked (deltaT12). The third time measured will be the time that the second photogate is blocked (delt aT2). The average velocity that it takes for the flag to pass through each photogate will be calculated by the change in the known distance of the flag divided by the time it takes to pass through the photogate in question. The acceleration of the cart can then be calculated by equation 1.2. A = V2-V1 / DeltaT12 Equation 1.2 The next experiment will be the measurement of acceleration due to a horizontal force, measured by a single photogate. The force will come from a weight hanging vertically from a string that runs through a pulley that is connected horizontally to the cart, measure by a single photogate. Figure 1.3:Horizontal Force cause by Hanging Weight The acceleration can be expressed by considering three free body diagrams. First the sum of the Y forces on the hanging weight. Ó F(y) = mg Ââ€" T1 = ma Equation 1.3 Notice that T1 is equal to mg Ââ€" ma. Next, evaluate the sum of the horizontal forces acting on theShow MoreRelatedPhysics Lab Report1059 Words   |  5 PagesGrade 11 physics: SPH3U1-01 | Physics Lab Report | Specific Heat Capacity of Brass | | Jin Jin Shi | 2012/12/6 | Instructor: Mr. Nailer | I. Introduction The amount of heat required to raise the temperature of a solid body depends on its change in temperature (ΔT), its mass (m), and an intrinsic characteristic of the material forming the body called specific heat (cp). The heat is calculated from the equation II. Purpose The purpose of this laboratory is to determineRead MorePhysics Lab Report717 Words   |  3 Pages (g) The steps (c) and (d) were repeated to obtain new values of Ã…Å"e and then step (e) to obtain a new curve III. The process was repeated till reasonably accurate values of F and P were obtained. However, it was seen that the third trial did give sufficiently accurate values, for all practical purposes. To obtain the safe pile capacity, a factor of safety of 2 on the ultimate skin friction resistance and 2.5 on the ultimate point bearing resistance was applied. 1.3.6 The same graph was also solvedRead MorePhysics Lab Report Impulse1163 Words   |  5 PagesImpulse and Momentum Lab Part I: As the first lab of the Physics 2 curriculum, our class completed a lab experiment that introduced us students to a new concept that would be a foundation to the future topics that we learn in this class. In this lab activity, we used a lab cart on a flat track to compare the collision of the cart with a force sensor with and without the plunger during different trials. The materials that we would need for this activity are a lab cart on a flat track, a timerRead MorePhysics Speed of Sound Lab Report743 Words   |  3 PagesSamantha Mackey 13. 2nd hour PHYSICS LAB REPORT: SPEED OF SOUND Purpose: In this lab, we will be doing 3 major things: 1) Collecting and organizing data to obtain resonant points in a closed pipe, 2) measure the length of a closed-pipe resonator, and 3) analyze the data to determine the speed of sound. Procedure: 1. Fill the graduated cylinder nearly to the top with water, with a tall glass tube open at both ends (the water level with act as the closed end). 2. DetermineRead MorePhysic Lab Report Parallel Force1409 Words   |  6 PagesPhysics Lab Report: Parallel Force Aim: To test the principle of moments. Apparatus: Metre rule with holes drilled at the 25cm, 50cm and 75cm mark, 50g masses 50mm long bolt with a diameter of approximately 5mm, retort stand, boss head and clamp, 0-10 N spring balance, electronic pan balance ,wire or string for suspending masses from the metre rule, two bulldog clips. Part A: Balancing a constant moment. Procedure: 1. The experiment is set up by first placing the bolt through the rule, thenRead MorePhysics Archimedes Principle Lab Report1288 Words   |  6 Pages| Buoyant ForceB=Δmg=Ï f VobjgThis equation was used to calculate the buoyant force of an object. | Experimental Procedure: ProcedureA: * Setup similar to the spring constant lab * Use the same or a similar spring from the spring constant lab * Find the spring constant of the smallest spring used from previous lab if not already foundB: * Use the same metal rod from the Error of Propagation experiment and attach it to the bottom of the spring * Fully submerged the metal rod in a beakerRead MorePhysics Lab Report Cooling Coffee1449 Words   |  6 PagesCooling Coffee Name: Diana Rusina Date:23.11.12 In this practical, you will be assessed on Design, Data Processing amp; Presentation and Conclusion amp; Evaluation – Read the checklist of the criteria for guidance. Introduction: It is Saturday afternoon. You brew yourself a cup of coffee and are just about to pour cold milk into the coffee. The doorbell rings and you realize immediately that your friend needs your help for a few minutes this afternoon. If you want to have yourRead MorePhysics Lab Report On Using A Simple Pendulum Model932 Words   |  4 PagesLaboratory report – First Draft Determine the acceleration due to gravity using a simple pendulum Objective The objective of this practical is to determine acceleration due to gravity ‘g’ using the simple pendulum model. This is shown when a period of oscillation is seen to be independent of the mass of the mass ‘m’. Theory A simple pendulum consists of a mass that is attached to a string of length ‘L’ that is fixed to a point, in this case, a cork suspended by a clamp stand. This allows theRead MorePhysics Lab Report - What Keeps a Stopper Moving in a Circle948 Words   |  4 Pagesthe error associated with calculating the speed of the stopper. In other labs you have used multiple data runs and averaged the data to minimize the random error associated with measuring. Why did you not have to do that on 5. To get the most accurate time we had the person timing also count the revolutions of the stopper. And we didn’t have to do multiple data runs because the time is the least important In this lab we found that the variables of circular motion are directly related. We accomplished

No comments:

Post a Comment

Note: Only a member of this blog may post a comment.